Bently Nevada 330191-40-75-05-05 Proximity Probe

Produto Introduction

TenBN offers the genuine Bently Nevada 330191-40-75-05-05, a proximity probe built for the demands of continuous machinery protection. The component is held in inventory for fast shipment to plants operating turbines, compressors, pumps, and other rotating assets.

Technical Parameters

• Modelo: 330191-40-75-05-05
• Produto Type: Proximity Probe
• Séries de Produtos: 330191 / 330195
• Unthreaded length Option: 40 – 4.0 in
• Overall case length Option: 75 – 7.5 in
• Total length Option: 05 =0.5 meter (1.6 feet)
• Agency approval Option: 05 = CSA, ATEX, IECEx Approvals
• Extension cables with an Option: al FluidLoc
• Cable Option: This option prevents oil and other
• Total probe lengths: 0.5, 1, 1.5, 2
• Lengths: 0.5, 1, 1.5, 2, 5, or 9
• Gap: 90
• Probe: 0.0045

Parâmetro Analysis

Each option block in the 330191-40-75-05-05 part number defines one element of the hardware configuration, from mechanical dimensions to connector style and approval suffix. The unthreaded length Option specifies 40 – 4.0 in. The overall case length Option specifies 75 – 7.5 in. The total length Option specifies 05 =0.5 meter (1.6 feet). The unit is rated for operation from -55°C to +232°C. Compliance documentation covers cSA, ATEX, IECEx Approvals.

Probe performance is specified together with the matching extension cable and Proximitor, so replacing the complete loop under consistent part numbers preserves the calibrated scale factor and linearity of the measurement chain.

Aplicação Scenarios

Typical duty for this probe is continuous shaft monitoring on critical rotating machinery, where it provides the raw vibration and position signals for alarm and trip logic in the associated monitoring rack.

Installation Guide

Thread the probe into its tapped hole, respect the thread engagement limits of the case, and mate the connector to the matching extension cable. Set the initial gap according to the electrical requirements of the associated Proximitor and verify the gap voltage against system documentation before returning the machine to service.

Compatibility

This component belongs to the 3300 XL 8 mm proximity system and is engineered to work with the associated probes, extension cables, Proximitors, and monitoring hardware of the same system. Bently Nevada components sharing the same part number are fully interchangeable, so a stocked spare can be fitted without re-engineering the measurement loop. TenBN can supply the complete chain under consistent part numbers.

Maintenance Advice

Inspect the probe tip, threads, and cable jacket at each outage for wear or damage, and confirm connector seating and torque have not relaxed in service. Keep the unit within its -55°C to +232°C operating envelope in service and storage.

Procurement Advice

This unit is supplied new & original in factory packing with 12 months factory warranty. Confirm the complete part number against your machine’s bill of materials before ordering, since each option digit changes the mechanical or electrical fit. TenBN stocks genuine Bently Nevada components and provides the official service documentation for this model. For inventory, pricing, and lead time on the 330191-40-75-05-05, contact [email protected].

Frequently Asked Questions

What is the operating temperature range?

The unit is rated from -55°C to +232°C, covering the temperature extremes typical of turbomachinery installations.

What approvals or certifications does it carry?

Compliance documentation covers cSA, ATEX, IECEx Approvals. Confirm the approval suffix on your part number before ordering for hazardous-area use.

Can this spare be interchanged with existing components?

Bently Nevada components sharing the same part number are fully interchangeable, so this spare can replace an existing unit without recalibrating the loop when the complete part number matches.

How do I confirm the right part number?

Check every option digit against the machine bill of materials, then contact [email protected] with the full string; the TenBN team will confirm fit, stock, and documentation.